Learning how to ride a motorcycle is almost similar to learn how to drive a manual car. In both learnings, you have to concern about the care, cautions, and lots of things in your mind. However, to learn motorcycle riding, you have to be more concerned and careful.
Once you have acquired the knowledge of riding a motorcycle, then it would be so easier for you. But some tiny mistakes can lead to a really bad consequence. And the motorcycle accident is quite common and serious among us. You will find lots of such cases regarding motorcycle accident (i.e., Edmonton motorcycle accident)
In this writing, you will get to know the 7 basic steps to ride a motorcycle. So keep reading!
Ways on how to ride a motorcycle
Before riding a motorbike, there are some basic things you need to know. Again, if you are a beginner, you need to start carefully because any mishap can result in a severe accident. So lets know-how and from where you can start your learning process.
Before getting started:
The first thing you need to do is, you have to make sure that your motorcycle is ready for the road. There is some Motorcycle Safety Foundation’s acronym for the checklist, which is also known as T-CLOCS.
This checkout is not only for the first time, every time you ride a motorbike, but you also need to go through this checkout.
T: Tires and the wheels
C: Controls which includes the pedal, cable, and so on
L: Lights which includes a mirror, head and backlights, and so on
O: Fluid oil level.
C: Chassis (i.e. chain, suspension)
S: front stand, kickstand
It is really important to focus on the safety gear before mounting on a bike because even in a parking speed, some mistakes can lead you to a severe injury. So before riding on a bike, make sure that you wear as much as safety gear as possible.
And the safety gears can include armored clothing, helmet, gloves, and so on. It is always important to wear a helmet. When you are done with the safety gear, helmet, and so on, you will be ready for your ride.
Riding the motorbike:
No matter how tall you are, mounting to the motorbike for the first time can be awkward for you. With a little bit of practice, you will able to conquer that awkwardness. And your left leg should be bent a little bit, and your weight should be in the center.
Remember that your right leg will control the gear pad and the balance of your bike. And your hand should be lean on the bike handle and over the clutch and the breaks. And make sure that your looking mirror is adjusted before you are ready for the ride.
Acceleration and braking:
When you are ready for the bike riding, your right hand will have the control of the acceleration and the braking. These are the most important functions of a bike. By twisting the grip, you will get the acceleration. Your acceleration will depend on how much you are twisting it.
Twisting too much at an initial level of starting can cause big inertia, which can lead to severe consequences. Your right hand also controls the front brake of your bike. So it is important to know how to press the brake. And your right foot will control the rear brake of the bike.
Clutch and Gear:
The clutch is on your left-hand grip. The clutch of a bike does the same job that a car clutch does. It helps to engage and disengage the transmission and engine. When you squeeze the clutch, you are putting the bike in a neutral mode (even when your bike in gear).
And practice releasing the clutch with your left hand slowly. When your bike is in gear, you have to pull it to shift the gear and release it slowly to avoid bad lurch. Generally, a motorbike has five to six gears. And they follow a specific pattern.
Most of the bike has a shift pattern, which is the first gear is down and give up. And the neutral would be somewhere between the first and second gear. As following;
- Sixth gear
- Fifth gear
- Fourth gear
- Third gear
- Second gear
- First gear
You will need some time and practice to get the Neutral. When you will able to shift your gear in neutral, you will see ‘N’ in the bike display. And while changing the gear, you need to engage and smoothly disengage the clutch.
Starting the motorbike:
Unless you have a classic old motorbike, you will find an electronic switch that will help you to start the bike. If your bike engine is still not started, then maybe you need to warm up the engine by kicking. And make sure when you start the bike, your bike is in Neutral mode.
The most bike requires you to disengage the clutch while you start the bike. And this can be a precaution that you squeeze the clutch while you start your engine to avoid lurching forward. As you hold the start button, the bike engine should start.
Warming Up Bike Engine:
Nowadays, the practice of warming up the car engine becomes so outdated. But warming up the bike engine is still an essential part of the riding ritual. So make sure that your bike is providing smooth, consistent power when you begin your ride.
You should ride idly for 30 seconds to see if there are any issues like ambient temperature, oil capacity, and the displacement of the engine. You can also use your temperature gauge as a basic guide and to avoid revving the bike engine.
The bottom line:
Learning and riding a motorbike can be fun if you know the correct way of riding it. And until or unless you are maintaining and doing it in a safe and controlled manner. Always remember that safety will come first before the fun.
Beginners can take all the safety gear first and can do it practically because riding a bike is all about practical things. Moreover, you can also enroll for the practical bike classes and also can follow the above mentioned simple steps to know the bike basics.